Dron iFlight Protek35 w wersji HD z zestawem Vista Polar, wersja pod baterie 4s z odbiornikiem TBS Crossfire, kolor szary.

Jeżeli potrzebujesz do drona wydruk 3D do montażu GoPro, to napisz do nas na kontakt@dronostrefa.pl Mamy drukarki 3D i możemy wydrukować taki uchwyt dodatkowo. 

Poniżej specyfikacja ze strony producenta:

After our very popular 3inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use. 

Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here... 

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it's 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves. 

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization). 

Durable plastic protectors with copper standoffs, portable compact design, easy accessable UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery.

Need a naked GoPro case or mount? Checkout our new iFlight naked GoPro Hero8 TPU case to use with your ProTek35. LINK

Changelog:

February 2021: Upgraded Prop Guards for more durability (Prop Guards V2.0, Material optimized)

April 2021: Upgraded Beast F7 45A V1.0 to V1.1 (Circuit design optimized, Updated to DPS310 Barometer)

*Barometer can only be used with Betaflight 4.3.0 and above!

September 2021: Upgraded Beast F7 45A to Beast F7 55A V2

Features:

- ProTek35 Prop Guards V2.0

- No Props or frame in view!

- High performance True-AIO Board Beast Whoop F7 AIO 55A to save weight and space

- T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)

- Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)

- Low Resonance frame construction (Less Jello, more Cinematic footage)

- Caddx Polar Vista Digital HD System

- Butter smooth 2203.5 3600KV (4S) (LINK) / 2205 2300KV (6S) (LINK)

- Pre-tuned with smooth freestyle settings

PRE-TUNED & PRE-SETUP:

Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

ProTek35 BNF Specs:

*Board Beast Whoop F7 AIO 55A (LINK)

*Motor: XING 2203.5 3600KV (4S) (LINK) / XING 2205 2300KV (6S) (LINK)

*Wheelbase: 151mm

*Body Size: 118*94.5mmmm

*Bottom plate thickness: 3.5mm

*Top plate thickness: 2mm

*Top and bottom plate spacing: 20mm (aluminum standoff height) 

*Propeller size: 3.5 inch

*FC pattern: 25.5*25.5mm / 20*20mmmm

*FPV cam spacing: 20mm

*Weight: 348.3g (without battery)

ProTek35 HD Quad BNF Included Components and Parts

pre-built and tested Quadcopter

1 x ProTek35 Frame

1 x Caddx Polar Vista Digital HD System Kit 

1 x Albatross LHCP Antenna ipex 170mm

1 x TPU Bracket for Nebula Nano Air Unit

1 x TPU Antenna holder

2 x Nazgul 3535 propeller (Set of 4 - Color May Vary)

1 x iFlight Lipo Strap 15*150mm (Color May Vary)

1 x  iFlight Lipo Strap 15*250mm (Color May Vary)

1 x GoPro TPU bottom stand black (GoPro Protector not included)

FC // Beast F7 AIO 55A V2 (LINK)

• MCU: BGA-STM32F745

• Gyro: BMI270
• Blackbox: 16MB Onboard Flash

• BEC output: 5V 2.5A 

• Barometer: DPS310

• Connector: Micro-USB

• OSD: IFLIGHT OSD (AT745E）
• FC Firmware：IFLIGHT_F745_AIO_V2
• Mounting pattern: 25.5*25.5mm φ3mm

• Dimensions: 32.5*32.5mm
• Weight: 8.5g

ESC // 55A 2-6S (LINK)

• Uarts: 5

• Current Sensor: Yes

• Input: 2-6S LIPO

• Current scale: 100
• Constant: 55A / Burst: 60A

• BLHeli: BLHeli-S

• Telemetry: no

• ESC Firmware: G-H-30 BLS
• Mounting pattern: 25.5*25.5mm/Φ3mm

• Dimensions: 32.5*32.5mm